Home > Att Uverse > At&t Wireless Box Not Working

At&t Wireless Box Not Working

Contents

If I go back into a show we have listed on series, and make recording changes and then save, then that show will show up on the "scheduled to record" list, It finally worked. Launch Troubleshoot & Resolve Tool Online Support Connect with a service representative and get assistance with your AT&T service. The cables are snuggly tightened, adapter plugged in, receiver not overheating. Check This Out

If they have the same issue they will know how to solve theirs" Award for Community Excellence (A.C.E.) achiever for 2016* *The views and opinions expressed on this forum are purely Needless to say it did not fix the problem. Reply satveer says: December 13, 2014 at 1:45 pm i just got att uverse. Guess it's time for another hour or more on the phone with tech support to get it replaced. my response

Att Uverse Tv Is Not Available At This Time

I am having this exact problem.Both of my wireless receiverslose the Cisco WAP signal. We go through the process of power cycling both the access point and the wireless receiver and it usually works for the next 24 hours or so. Checkfor Interference Make sure there are no devices around the Wireless Access Point or Wireless Receiver that can cause interference, such as cordless phones, baby monitors, etc... Re: Wireless receiver loses connection to access point Post Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 11 of 191

Does anyone have any suggestions? Some customers don't call and then the alarm tells them several days later that it can't communicate when it attempts to send a test signal. Hello cindyh5161, I'm sorry you are experiencing the same issue with your Wireless Access Point for your receiver. At&t U Verse Tv Is Not Available At This Time Restart Receiver We always prefer a direct connection to our U-verse router due to the Quality of Service control it offers.

I reset the modem, ran through tests with the technician on the phone, but they can't figure it out. I only have Internet on this box, called technical support, was told line was checked and is fine… Question… My friend has a router that was sent to them as a We Have Advice! I was able to resetablish connectivity by un plugging and re-plugging the network cable, or disconnecting and reconnecting the power, but now neither allow it to connect to the main 2

AFTER we purchased UVerse we had the same issue - we have 4 kids, so you can imagine the chaos in our house… When I called they said we only get Att Uverse Reset Receiver Message We usually also get a glitch in the picture when we turn those same switches "on". This is not only me complaining but 6 other individuals living in our apartment complex. There are just the basic steps that you should make on your own before getting frustrated, but there is more.  Sometimes the wiring in a property, or even those done by

Uverse Wireless Box Won't Connect

Following the install, if a customer had a fire or emergency requiring the system to communicate for police response, it can not communicate. https://www.att.com/esupport/article.html#!/u-verse-tv/KM1009882 After that, hopefully that sorts out everything, and everything will continue to route as normal. Att Uverse Tv Is Not Available At This Time ATT said they're sending us a new router, which is fine, but we have work to do before then. Att Uverse Not Available At This Time Restart Receiver We've got your wireless devices covered with thousands of hotspot locations across the U.S.

I am an AT&T employee and the postings on this site are my own and don’t necessarily represent AT&T’s position, strategies or opinions. *I am an AT&T employee and the postings http://sohohosting.net/att-uverse/at-t-wireless-receiver-dvr-not-working.html All techs said all lines, inside and outside, were fine. Connecting the Wireless Access Point Connecting the Wireless Receiver Checkpower/signal strength and reboot Confirm you have power. Hello lwoxen , I was working on your issue with david_t and have sent you a private message as well. Att Uverse Troubleshooting No Signal

Re: Wireless receiver loses connection to access point Post Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 24 of 191 Troubleshoot U-verse: Picture and Sound (3:10) View messages waiting on your TV Sometimes we need to send you messages about your service. Does anyones know how to change it? this contact form Reply Ginaw says: November 15, 2011 at 11:05 am Hi 🙂 lately, the picture on my tv has been bad off and on.

Also we have 5 boxes, and only one room can watch TV in HD. Http //www.att.com/wireless Tv Re: Wireless receiver loses connection to access point Post Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 12 of 191 I usually cannot re-establish a connection for hours.

Reply John says: June 27, 2014 at 11:23 am Why can't I play recordings stored on my Uverse VIP2250 dvr when the Uverse signal is stopped?

I have 2 wireless receivers and both will lose connectivity to the WAP. The access point is connected to the gateway via cat5 on s direct port (ie not through a switch). Disconnect the DVR All the receivers in the house have to pair with the DVR through for DVR content. Att Uverse Tv Is Not Available At This Time Restart Receiver I replied to the e-mail that you sent ot me but I still have had no response and AT&T does not show an order for this.

I am an AT&T employee and the postings on this site are my own and don’t necessarily represent AT&T’s position, strategies or opinions. *I am an AT&T employee and the postings Here is a good source for cat5 cable - monoprice.com Award for Community Excellence (A.C.E.) achiever for 2016* *The views and opinions expressed on this forum are purely my own. If it will require some kind of activation or needing to change multiple things to use it, I may just have someone come replace it, but if not, I'd love to http://sohohosting.net/att-uverse/at-t-u-verse-wireless-not-working.html It seems that it should behave like a laptop - I turn that off or unplug it and I don't lose everything on my hard drive.

I would be fine just swapping them out for non-wireless, or having this issue fixed, either way. Reply marie says: August 20, 2011 at 10:13 am i had my tv on this morning and the power went off, when the power came back on, the tv is all Comcast Xfinity vs Verizon Fios: A Thorough Comparison AT&T U-verse vs. Reply Bill says: January 14, 2015 at 3:42 pm Try unplugging the power from your box for at least 10 seconds (I do 30 seconds) then plugging it back in.

Close× Sign up Join the Community AT&T Employee ID We will use your e-mail address for communications related to your registration and participation. If no lights are on, ensure that the TV Receiver is turned on by pressing and releasing theAT&Tbutton on the remote control, and then pressing and holding thePOWERbutton on the receiver Is this normal or do I have a DVR problem? I can help you determine if it needs to be replaced.

Following a successful pairing, unplug the Wireless TV Receiver and reconnect it at the desired location. Nothing has spilled on it and it is clean (no dust). This stuff is all still plugged in.